WEN 3401 5.7-Amp 660 CFM Dust Collector with 12-Gallon Bag and Optional Wall Mount

WEN 3401 5.7-Amp 660 CFM Dust Collector with 12-Gallon Bag and Optional Wall Mount

    Features:

  • 5.7-amp motor moves over 660 cubic feet of air per minute
  • 4-inch dust port allows for connection to your favorite woodworking tools
  • Four swivel casters lock in place to prevent unwanted movement during operation
  • Compact design features onboard carrying handle for easy storage and transportation
  • Mount the unit to the wall of your shop for accessible dust collection whenever you need it

WEN 3410 3-Speed Remote-Controlled Air Filtration System (300/350/400 CFM)

WEN 3410 3-Speed Remote-Controlled Air Filtration System (300/350/400 CFM)

    Features:

  • Includes a 1-micron filter and a 5-micron pre-filter, both of which can be easily replaced
  • Dimensions – 17” L x 20.5” W x 10” H | Electrical Requirements – 120V, 60 Hz, 1A | Air flow – 300/350/400 cubic feet per minute | Cover rooms up to – 400 sq ft. | Noise rating – 50 to 60 dB
  • Programmable timer automatically shuts unit off after set number of minutes
  • Remote control allows users to set timer, change speed and power the unit on and off from up to 26 feet away
  • RF remote system allows for operation from any angle of the room, even if direct line of vision is obstructed

SHOP FOX W1685 1.5-Horsepower 1,280 CFM Dust Collector

SHOP FOX W1685 1.5-Horsepower 1,280 CFM Dust Collector

    Features:

  • Powder coated paint
  • Bag volume: 5.4 cubic feet
  • Static pressure: 10.1-Inch. Interior Hose Diameter (In.) – 6
  • Air suction capacity: Approximately 1,280 CFM
  • Standard bag filtration: 2.5 Microns

The Dust Deputy Deluxe Anti-Static Cyclone Separator 5 Gallon Kit

The Dust Deputy Deluxe Anti-Static Cyclone Separator 5 Gallon Kit

    Features:

  • INCREASED SUCTION POWER – The ORIGINAL shop vacuum cyclone, now 20% more throughput (CFM) and efficiency with Neutral Vane Technology, Oneida Air Systems’ patented Dust Deputy cyclone uses centrifugal force to capture and remove 99% of dust and debris from the air-stream before it reaches your vacuum filter, eliminating clogged filters and suction loss!
  • LONGER LIFESPAN – Prevents fine dust and large debris from reaching your dust filter, reducing the need for cleanings and prolonging the lifespan of your filter. The Dust Deputy Deluxe will save you countless time and money on expensive replacement vacuum filters and dust bags, allowing you to keep working harder, longer, and safer than ever!
  • WET OR DRY – This simple and efficient design can be adapted for use with any make, size, or model shop vacuum and features tapered 2.0″ ports for secure fittings using a variety of dust collection hose sizes. Portable design can be mounted directly to the vacuum. Works with most materials: Wood dust, drywall dust, concrete dust, clay/silica dust, blasting soda, cooled ash & soot, water, metal shavings, baking flour, grass & leaves, pet/animal hair, pharmaceutical waste, and much more!
  • MADE IN AMERICA – The ORIGINAL (and still the best), the Dust Deputy cyclone is designed, patented & manufactured in the USA by American workers. Don’t be fooled by poor performing & cheap imitations with metric inlets & outlets that don’t fit standard (SAE) hoses. Comes with everything you need to convert your shop vacuum into a two-stage, dust-free system: the anti-static cyclone, SD hose, elbow adapters, 5-gallon 100 mil heavy-duty buckets, caster wheels, gasket, & mounting hardware.
  • US Pat. 6833016, RE40048, 7282074

Dust Deputy Anti-Static Cyclone Separator (DD DIY)

Dust Deputy Anti-Static Cyclone Separator (DD DIY)

    Features:

  • INCREASED SUCTION POWER – The ORIGINAL shop vacuum cyclone, now 20% more throughput (CFM) and efficiency with Neutral Vane Technology, Oneida Air Systems’ patented Dust Deputy cyclone uses centrifugal force to capture and remove 99% of dust and debris from the air-stream before it reaches your vacuum filter, eliminating clogged filters and suction loss!
  • LONGER LIFESPAN – Prevents fine dust and large debris from reaching your wet/dry vacuum’s filter, reducing the need for cleanings and prolonging the lifespan of your filter. The Dust Deputy DIY will save you money on expensive replacement filters and dust bags, and time, allowing you to focus on the task at hand.
  • WET OR DRY – This simple and efficient design can be adapted for use with any make, size, or model shop vacuum and features tapered 2.0″ ports that fit the cuffed 2.5” hoses that come standard with most shop vacuums. Works with most materials: wood dust, drywall dust, concrete dust, clay/silica dust, blasting soda, cooled ash & soot, water, metal shavings, baking flour, grass & leaves, pet/animal hair, pharmaceutical waste, and much more!
  • MADE IN AMERICA – Designed, patented, & manufactured in the USA, our Dust Deputy DIY (Do-It-Yourself) cyclone lets you build the dust control system that’s right for you. Contains the anti-static cyclone separator, gasket, & mounting hardware. You supply the waste container, the hose, etc. With the Dust Deputy DIY cyclone, you’re limited only by your imagination! Note: If used with a 5-gallon bucket, the bucket must be a minimum of 90 mils thick or else it may collapse under vacuum pressure.
  • US Pat. 6833016, RE40048, 7282074

KEPKGO Dust Collector Cyclone Filter Collector Sixth Generation SN50T6 Turbo Vacuum Cleaner Separation Catcher Turbo Industrial Bagless with Flange Separator Cleaning Power Woodworking Tools DIY…

KEPKGO Dust Collector Cyclone Filter Collector Sixth Generation SN50T6 Turbo Vacuum Cleaner Separation Catcher Turbo Industrial Bagless with Flange Separator Cleaning Power Woodworking Tools DIY…

    Features:

  • Points for attention: In order to ensure the normal use of cyclone dust collector, the inlet air volume must be far greater than the dust content, the minimum air intake must be greater than 70%, otherwise there will be “choking dust” phenomenon, that is, a large amount of dust into the vacuum.
  • This is because the working principle of the cyclone dust collector is different from that of the bag dust collector, so it is absolutely impossible to use the cyclone dust collector like a pumping unit, and bury the suction nozzle in the dust. If you do that, because there is no air in the dust collector or or the air content is too small, the upward discharge can only be “ash”!
  • Can completely replace: bag-type dust removal equipment, it has: simple manufacturing process, ultra-low production costs, lower operating costs, dust removal efficiency and pressure constant, basic maintenance-free advantages are incomparable bag-type dust removal.
  • The working principle of cyclone collector is: The mixture of dust and gas enters the dust collector along the horizontal pipe, rotates and settles at a high speed downward along the wall of the barrel, and “dust” falls into the dust barrel below under the strong centrifugal force and its own gravity, and the clean dust gas is discharged upward along the central pipe.
  • The sixth generation turbocharged cyclone dust collector is widely used in all industries, such as machinery, textile, household appliances, food, grain, coal, cement, building materials, thermal power, metallurgy, steel, sweeper, dust removal equipment manufacturing and personal processing center manufacturing dust removal facilities.

POWERTEC DC5370 Wall Mounted Dust Collector with 2.5 Micron Filter Bag | 537 CFM

POWERTEC DC5370 Wall Mounted Dust Collector with 2.5 Micron Filter Bag | 537 CFM

    Features:

  • Includes: (1) wall hanging dust collector with mounting bracket and (1) 2. 5 micron dust collector filter bag
  • Reusable micron bag: ensures optimal air quality, free from harmful pollutants and fine dust particles – comes with built-in window to view dust level and an easy-dust disposal zipper
  • Compact size is ideal for small Pro or hobby shop
  • “Power specs: features 1 HP electric motor with dual voltages 120V/240V | 7 amp at 120V, 3. 5 amp at 240V; motor speed: 3450 RPM | airflow capacity – 537 CFM”
  • “Compatibility: possesses a 4 inch Inlet port – allowing you to attach the dust-collector hose directly to whatever machine you are using “

PSI Woodworking DBGULP Big Gulp Dust Hood

PSI Woodworking DBGULP Big Gulp Dust Hood

    Features:

  • Dust hood with a 13-by-16-inch opening
  • Perfect for miter saws, lathes, radial arm saws, carving, sanding, and planers without hoods
  • Lightweight and portable; made from tough ABS plastic
  • 4-inch port to connect to any dust collection system
  • Weighs 2.2 pounds

BUCKTOOL 1.2 HP Auto Start 750CFM Dust Collector with 3 Dust Collection Bag, 5.4 Cubic Bag Capacity and 5 PCS Reducer for Woodworking DC50

BUCKTOOL 1.2 HP Auto Start 750CFM Dust Collector with 3 Dust Collection Bag, 5.4 Cubic Bag Capacity and 5 PCS Reducer for Woodworking DC50

    Features:

  • Power:1.2 HP, 120V motor, 3450 RPM,750CFM CSA listed . Full load Amp 6.5A.
  • Auto-start function:User friendly auto-start function provides power outlet for your power tools, no longer need to find a new outlet for your tools but also reduces the trouble of frequent opening and closing, can be connected with machine 7A Max
  • Easy bag install:The well-designed clasp makes bag install and removal easy, soft PET bag clamp won’t cut your hand
  • Versatile size: features a portable base size of 16-1/2 x 26-3/8 inches and caster wheels, working as both a mobile or stationary compact dust collector unit that maximizes shop space
  • Include: 5 pcs reducer; 5 ft. x 4 in. dia. flexible dust extraction hose; Plastic Lower collection bag; cloth lower collection bag; 2.5-micron Cloth upper collection bag; PET bag clamp

POWERTEC 70103 21-Inch Floor Sweep

POWERTEC 70103 21-Inch Floor Sweep

    Features:

  • Overall size: 24-Inch width by 3 1/2-Inch height by 7-Inch diameter
  • Flange is 3/4-Inch wide
  • Material thickness: 3/32-Inch
  • Outlet diameter: 4-Inch
  • Weight: 6. 2 oz

As an Amazon Associate I earn from qualifying purchases.

Random products:

valspar deck stains
ocora